ALPHA 2022-09-22-01
ALPHA 2022-09-22-01
A new Alpha version is available
https://opengd77.com/downloads/MDUV380/ ... 416608b4e2
This includes
* Changes to DTMF FM Tx.
NOte. Audio tones of the DTMF to the speaker has been disabled, to fix this problem.
* Fix for GPS on newer radios
GPS power is enabled when you goto the GPS page of the Radio Info screen. But the power is not turned off when leaving this screen.
So at the moment to turn off the GPS power, you need to turn the radio off and on again after viewing the GPS page.
This is just temporary functionality, becuase in the long term, the GPS functionaliy will be moved to a separate menu screen and there will be a setting in General Opions to enable / disable GPS power
The GPS in these radio is not sensitive. It will normally not work when indoors, and even outdoors it can take 5 minutes before the GPS has obtained a fix.
If you go to the GPS screen, and the radio constantly says "No GPS data" your radio does not have a GPS module, or the module is faulty.
Normally if you have a GPS version of the radio, the GPS screen will show the text "Acquiring" after about 1 second, to indicate the firmware is receiving data from the GPS module.
* Fix for VFO Scan.
Long Press Up arrow to enter scan mode
Long Press Down arrow to exit scan mode
* Fixes for VFO Sweep Scan
Gain is controlled by the rotary controller knob on the top of the radio
Up and Down arrows change the center frequency. Note Up and Down arrow direction of change is probably the opposite to the way it should be, however this will be fixed when we change the operation of the Up and Down buttons on all menus
SK2 + Up / Down changes sweep bandwith
Note. The VFO Sweep Scan UI functionality is not fully working yet
https://opengd77.com/downloads/MDUV380/ ... 416608b4e2
This includes
* Changes to DTMF FM Tx.
NOte. Audio tones of the DTMF to the speaker has been disabled, to fix this problem.
* Fix for GPS on newer radios
GPS power is enabled when you goto the GPS page of the Radio Info screen. But the power is not turned off when leaving this screen.
So at the moment to turn off the GPS power, you need to turn the radio off and on again after viewing the GPS page.
This is just temporary functionality, becuase in the long term, the GPS functionaliy will be moved to a separate menu screen and there will be a setting in General Opions to enable / disable GPS power
The GPS in these radio is not sensitive. It will normally not work when indoors, and even outdoors it can take 5 minutes before the GPS has obtained a fix.
If you go to the GPS screen, and the radio constantly says "No GPS data" your radio does not have a GPS module, or the module is faulty.
Normally if you have a GPS version of the radio, the GPS screen will show the text "Acquiring" after about 1 second, to indicate the firmware is receiving data from the GPS module.
* Fix for VFO Scan.
Long Press Up arrow to enter scan mode
Long Press Down arrow to exit scan mode
* Fixes for VFO Sweep Scan
Gain is controlled by the rotary controller knob on the top of the radio
Up and Down arrows change the center frequency. Note Up and Down arrow direction of change is probably the opposite to the way it should be, however this will be fixed when we change the operation of the Up and Down buttons on all menus
SK2 + Up / Down changes sweep bandwith
Note. The VFO Sweep Scan UI functionality is not fully working yet
Re: ALPHA 2022-09-22-01
Update
In addition to the fixes listed above.
This version now fixes the DMR Tx bug when the radio has been idle and is in power saving mode when the PTT is pressed.
downloads/MDUV380/Firmware/b86e271149df ... 1533437d7d
In addition to the fixes listed above.
This version now fixes the DMR Tx bug when the radio has been idle and is in power saving mode when the PTT is pressed.
downloads/MDUV380/Firmware/b86e271149df ... 1533437d7d
Re: ALPHA 2022-09-22-01
Is the firmware update a matter of pointing to the new .bin file in the GD77 CPS "extra" menu and loading, or are there other required steps?
Thanks, this is excellent stuff.
Mark K5LXP
Albuquerque, NM
Thanks, this is excellent stuff.
Mark K5LXP
Albuquerque, NM
Re: ALPHA 2022-09-22-01
Yes, If you already have an MDUV380 running the firmware you just need to put the radio into firmware update mode and upload the .bin file using the Extras Menu.
Colin G4EML
Colin G4EML
Re: ALPHA 2022-09-22-01
You need also need official bin for the MD9600 which provides the AMBE codec.
For legal reasons, we can't include the AMBE codec in the binary,
See the detailed instrallatin instructions
Re: ALPHA 2022-09-22-01
Sorry, I don't understand what you are saying.
The colour code scan works as it should on the VFO screen.
The colour code scan works as it should on the VFO screen.
Re: ALPHA 2022-09-22-01
Note. The JA_ version is the Japanese language versionjamaxsantos wrote: ↑Sun Sep 25, 2022 6:14 pmHello, please which file should I choose to send to the radio, JA_Open or Open? Thanks
Re: ALPHA 2022-09-22-01
Contacts and channels will be erased.jamaxsantos wrote: ↑Sun Sep 25, 2022 7:54 pmjamaxsantos wrote: ↑Sun Sep 25, 2022 7:51 pmThank you very much, I'm new to GD77 and to the forum too, I would never have imagined it, learning little by little.
When an update is made, is it necessary to import the csv contacts again or not?
Re: ALPHA 2022-09-22-01
Hi,
When updating the firmware, the codeplug, dmrid database and keplerian elements aren't touched.
Cheers.
---
Daniel
When updating the firmware, the codeplug, dmrid database and keplerian elements aren't touched.
Cheers.
---
Daniel