Eco Levels
Re: Eco Levels
Hi,
You could try to pull out the battery for few seconds, then reinsert it.
I just flashed this "Clear_beep_buffer_and_set_hardware_audio_path", nothing strange, boot melody is playing fine. The only noticeable this is a small delay between the power on and screen init (but I didn't try the previous versions).
Cheers.
---
Daniel
You could try to pull out the battery for few seconds, then reinsert it.
I just flashed this "Clear_beep_buffer_and_set_hardware_audio_path", nothing strange, boot melody is playing fine. The only noticeable this is a small delay between the power on and screen init (but I didn't try the previous versions).
Cheers.
---
Daniel
Re: Eco Levels
Possibly the changes I applied to prevent bus contention when playing the boot melody can cause deadlock.F1RMB wrote: ↑Thu Feb 18, 2021 10:22 amHi,
You could try to pull out the battery for few seconds, then reinsert it.
I just flashed this "Clear_beep_buffer_and_set_hardware_audio_path", nothing strange, boot melody is playing fine. The only noticeable this is a small delay between the power on and screen init (but I didn't try the previous versions).
Cheers.
---
Daniel
I need to add a timeout to prevent deadlock, and perhaps delay longer than 0 !
I agree.
Turn the radio off.
Remove the battery.
Press SK1 + SK2 and turn on the radio
Bootloader should run. (Green LED)
Load version from 16th Feb which is stable
Re: Eco Levels
After repeated attempts, I managed to put the radio in the bootloader and I have the firmware from February 16, 2021.
I can continue testing.
I can continue testing.
Re: Eco Levels
Don't use the latest version I posted, because perhaps it hangs sometimes during boot.
I will need to modify the last version to stop the radio from hanging.
PS. What percentage is you battery ?
Re: Eco Levels
Re: Eco Levels
OpenGD77_Suspend_Reset_I2S
I tested about 7 hours this versión, reset before start with SK2 and apply all the params, and works very well i test level 3 and level 4.
Prompt is beep and level of beep about 3 db, if beep are down of 0 db appears to start again the bug.
QSO's from different TG's sounds very well, changing from one to another TG, i put TS on and also i changed from TS 1 to TS2 and listen Qso's without interruption, from time to time i speak to parrot PC 9990 and also works.
Battery saver appears also to work well, I exit house with 47 % and return with 36 %
I think that this version (with the beep over 0 db) and the full reset version are the best for now...
I tested about 7 hours this versión, reset before start with SK2 and apply all the params, and works very well i test level 3 and level 4.
Prompt is beep and level of beep about 3 db, if beep are down of 0 db appears to start again the bug.
QSO's from different TG's sounds very well, changing from one to another TG, i put TS on and also i changed from TS 1 to TS2 and listen Qso's without interruption, from time to time i speak to parrot PC 9990 and also works.
Battery saver appears also to work well, I exit house with 47 % and return with 36 %
I think that this version (with the beep over 0 db) and the full reset version are the best for now...
Re: Eco Levels
EA5SW wrote: ↑Thu Feb 18, 2021 5:25 pmOpenGD77_Suspend_Reset_I2S
I tested about 7 hours this versión, reset before start with SK2 and apply all the params, and works very well i test level 3 and level 4.
Prompt is beep and level of beep about 3 db, if beep are down of 0 db appears to start again the bug.
QSO's from different TG's sounds very well, changing from one to another TG, i put TS on and also i changed from TS 1 to TS2 and listen Qso's without interruption, from time to time i speak to parrot PC 9990 and also works.
Battery saver appears also to work well, I exit house with 47 % and return with 36 %
I think that this version (with the beep over 0 db) and the full reset version are the best for now...
OK.
I have an idea that perhaps the C6000 in your radio does not operate correctly with the new SPI transfer speed from the MK22 CPU.
I am busy today but I will make some test versions at the weekend
Re: Eco Levels
I am not sure whether this is related to the echo levels, but here is the best are in the forum that I thought it would fit. I am having some DMR "disconnects" from time to time. I am hearing someone and than I get silence, with the green light. I go to the Brandmeister Hoseline and I can hear the person did not stop talking. I need to turn the radio off and on again and I get the audio back.
I am running a GD-77 with the OCT 2 beta code, but this behavior happened before I loaded the latest beta.
I even tried to switch my hotspot (I got two duplex ones) and the result is the same. The DMR issue happened with the echo levels in all possible settings, even 0 which means no echo at all, hence I am not sure what could be causing the problem.
I am posting it here in case anyone has a hint for it. Thanks.
I am running a GD-77 with the OCT 2 beta code, but this behavior happened before I loaded the latest beta.
I even tried to switch my hotspot (I got two duplex ones) and the result is the same. The DMR issue happened with the echo levels in all possible settings, even 0 which means no echo at all, hence I am not sure what could be causing the problem.
I am posting it here in case anyone has a hint for it. Thanks.
Re: Eco Levels
If the radio is already receiving and the signal drops out, it won't be the Eco level, as this is only used when there is no signal.
The radio won't enter power saving when there is a signal
Do you have another DMR radio which you can run ar rhe same time to compare whether your hotspot is actually transmiting valid DMR signals the entire time.
The radio won't enter power saving when there is a signal
Do you have another DMR radio which you can run ar rhe same time to compare whether your hotspot is actually transmiting valid DMR signals the entire time.