Page 1 of 2
ALLCALL with GD77
Posted: Thu Dec 23, 2021 7:26 pm
by oe7abh
Hello,
TEST1: QSO Simplex-Channel:
Device1: GD77-TX with ALLCALL -> Device2: GD77-RX does
not open (DMR-FILTER RX-GROUP = ON)
TEST2: QSO Simplex-Channel:
Device 1: GD77-TX with ALLCALL -> Device 2: Anytone RX
opens (DMR FILTER RX-GROUP = ON)
Questions:
Which radio responds correctly?
TX with ALLCALL should always open the RX?
73 Alfred OE7ABH
http://tyrofly.at/funk.htm
Re: ALLCALL with GD77
Posted: Thu Dec 23, 2021 8:02 pm
by G4EML
Yes, allcall should be received by all radios.
OpenGD77 does not currently comply with this.
It’s probably not a high priority requirement though.
Re: ALLCALL with GD77
Posted: Fri Dec 24, 2021 12:15 pm
by oe7abh
Hi Colin,
Thank you for reply!
Impractical on simplex direct connections (call with ALLCALL), if other devices (GD77) work with RX group lists!
73 Alfred OE7ABH
http://tyrofly.at/funk.htm
Re: ALLCALL with GD77
Posted: Wed Dec 29, 2021 7:34 am
by VK3KYY
oe7abh wrote: ↑Fri Dec 24, 2021 12:15 pm
Hi Colin,
Thank you for reply!
Impractical on simplex direct connections (call with ALLCALL), if other devices (GD77) work with RX group lists!
73 Alfred OE7ABH
http://tyrofly.at/funk.htm
What is the Amateur Radio use case for this ?
Re: ALLCALL with GD77
Posted: Wed Dec 29, 2021 10:02 pm
by oe7abh
Hi Roger,
Thank you for reply !
145.375 Mhz = Simplex connections in the amateur radio club!
Noise-free connections are fun!
Thanks for your work ....
https://amateurfunk-bremen.forumieren.d ... -fm-und-dv
73 Alfred OE7ABH
http://tyrofly.at/funk.htm
Re: ALLCALL with GD77
Posted: Thu Dec 30, 2021 6:51 am
by VK3KYY
So why don't you use a TG for this ?
Re: ALLCALL with GD77
Posted: Thu Dec 30, 2021 8:04 am
by oe7abh
Hi Roger,
We are currently working with 2 channels:
145.375 is a call channel (CQ) according to the band plan, everyone should hear it (ALLCALL)!
For the QSO we use 144.8625 with TG99 so that the call channel is free again.
73 Alfred
Re: ALLCALL with GD77
Posted: Thu Dec 30, 2021 10:16 am
by VK3KYY
oe7abh wrote: ↑Thu Dec 30, 2021 8:04 am
Hi Roger,
We are currently working with 2 channels:
145.375 is a call channel (CQ) according to the band plan, everyone should hear it (ALLCALL)!
For the QSO we use 144.8625 with TG99 so that the call channel is free again.
73 Alfred
Do they hear the call if you don't have any DMR filters enabled.
Re: ALLCALL with GD77
Posted: Thu Dec 30, 2021 11:37 am
by oe7abh
- If I have not activated a DMR filter, I hear the call with ALLCALL!
- But there are OMs who have set a DMR filter - then the call does not come through!
Re: ALLCALL with GD77
Posted: Thu Dec 30, 2021 2:32 pm
by kt4lh
Can't you just all agree on a Simplex TG? I've heard TG99 often.
Or if you really want All Call, I think that's typically 16777215 so just program that in as an RX group if not already in Promiscuous mode?