MD-9600 mic pinouts
MD-9600 mic pinouts
I have looked around and I have come across two pieces of information on the pinouts for the MD-9600 microphone / jack. Unfortunately they do not align.
It would seem someone here would know exactly what the wiring of the RJ-45 for the microphone is. If possible may I be enlighten to such. I am looking to have custom cable built for the MD-9600 I use at my shack (base station).
Thanks in advance.
AA3RP
It would seem someone here would know exactly what the wiring of the RJ-45 for the microphone is. If possible may I be enlighten to such. I am looking to have custom cable built for the MD-9600 I use at my shack (base station).
Thanks in advance.
AA3RP
Re: MD-9600 mic pinouts
Someone made this drawing , I haven't verified that it's correct:AA3RP wrote: ↑Wed Nov 29, 2023 1:45 amI have looked around and I have come across two pieces of information on the pinouts for the MD-9600 microphone / jack. Unfortunately they do not align.
It would seem someone here would know exactly what the wiring of the RJ-45 for the microphone is. If possible may I be enlighten to such. I am looking to have custom cable built for the MD-9600 I use at my shack (base station).
Thanks in advance.
AA3RP
https://rclubvic.files.wordpress.com/20 ... md9600.pdf
Re: MD-9600 mic pinouts
I was the author of that document. It is amazing where it appears around the internet!
I can confirm that it is correct.
RJ45s are tricky to wire as the location of pin 1 is not well defined. It is easy to wire them up in reverse. I suggest double checking against a genuine microphone. If you look closely at the plug you can see the two not connected pins 7 and 8.
Colin G4EML
I can confirm that it is correct.
RJ45s are tricky to wire as the location of pin 1 is not well defined. It is easy to wire them up in reverse. I suggest double checking against a genuine microphone. If you look closely at the plug you can see the two not connected pins 7 and 8.
Colin G4EML
Re: MD-9600 mic pinouts
Thank you both for the timely response.
Colin it seems the PDF files that I have of this schematic are bit scans of a print out as the lines are not totally clear or consistent. Do you have an original digital file of this schematic. The reason I ask is because I will be sending it to the person who will use it to build the custom cable for me.
Please let me know either way and thank you for your work on the MD-9600 in every aspect. With the Open firmware and your hardware insights and mods the radio is born anew !!!
If I get brave I may even attempt the remote head option for one of the vehicles next year.
AA3RP
Colin it seems the PDF files that I have of this schematic are bit scans of a print out as the lines are not totally clear or consistent. Do you have an original digital file of this schematic. The reason I ask is because I will be sending it to the person who will use it to build the custom cable for me.
Please let me know either way and thank you for your work on the MD-9600 in every aspect. With the Open firmware and your hardware insights and mods the radio is born anew !!!
If I get brave I may even attempt the remote head option for one of the vehicles next year.
AA3RP
Re: MD-9600 mic pinouts
I also noticed the bad quality, I hope that Colin has a better one.AA3RP wrote: ↑Wed Nov 29, 2023 7:21 pmThank you both for the timely response.
Colin it seems the PDF files that I have of this schematic are bit scans of a print out as the lines are not totally clear or consistent. Do you have an original digital file of this schematic. The reason I ask is because I will be sending it to the person who will use it to build the custom cable for me.
Please let me know either way and thank you for your work on the MD-9600 in every aspect. With the Open firmware and your hardware insights and mods the radio is born anew !!!
If I get brave I may even attempt the remote head option for one of the vehicles next year.
AA3RP
But this one is a bit better than the first I linked to: https://www.miklor.com/MD9600/pdf/9600-Mic.pdf
Re: MD-9600 mic pinouts
That last document is as good as it gets. The original was an existing scanned diagram for a Yaesu microphone which is almost the same. I just modified it to suit.
Colin.
Colin.
Re: MD-9600 mic pinouts
Once again thank you to the both of you.
Good to know the history and what is out there.
The latest PDF should be ok and I will send it along.
AA3RP
Good to know the history and what is out there.
The latest PDF should be ok and I will send it along.
AA3RP
Re: MD-9600 mic pinouts
Colin,
Thank for the background and info on the mic wiring for the MD-9600.
I notice it only uses 6 of 8 possible wire positions. The question I have at this point is the RJ45 connector on the radio, does it have audio-out on either of pin 7 or 8. I have two reasons for asking. One is if audio out is on either pin 7 or 8 it might be possible to wire up a speaker / mic, and the second reason is that I am looking to get a cable for the Digirig device to experiment with sound card based digital modes for such things and WinLink and Vara FM.
Finally looking at the work you did to create the remote head (impressive) I am assuming you where on the radio PCB one could find a pad / connection point for routing to mic RJ45 connector if not already done so.
Thanks in advance.
Thank for the background and info on the mic wiring for the MD-9600.
I notice it only uses 6 of 8 possible wire positions. The question I have at this point is the RJ45 connector on the radio, does it have audio-out on either of pin 7 or 8. I have two reasons for asking. One is if audio out is on either pin 7 or 8 it might be possible to wire up a speaker / mic, and the second reason is that I am looking to get a cable for the Digirig device to experiment with sound card based digital modes for such things and WinLink and Vara FM.
Finally looking at the work you did to create the remote head (impressive) I am assuming you where on the radio PCB one could find a pad / connection point for routing to mic RJ45 connector if not already done so.
Thanks in advance.
Re: MD-9600 mic pinouts
According to the radio front panel schematic the other 2 pins are GNDAA3RP wrote: ↑Mon Dec 04, 2023 7:09 amColin,
Thank for the background and info on the mic wiring for the MD-9600.
I notice it only uses 6 of 8 possible wire positions. The question I have at this point is the RJ45 connector on the radio, does it have audio-out on either of pin 7 or 8. I have two reasons for asking. One is if audio out is on either pin 7 or 8 it might be possible to wire up a speaker / mic, and the second reason is that I am looking to get a cable for the Digirig device to experiment with sound card based digital modes for such things and WinLink and Vara FM.
Finally looking at the work you did to create the remote head (impressive) I am assuming you where on the radio PCB one could find a pad / connection point for routing to mic RJ45 connector if not already done so.
Thanks in advance.
Re: MD-9600 mic pinouts
As Roger says pins 7 and 8 are grounded in the front panel.
You might be able to disconnect those pins from ground and use them for audio but you might need to remove the whole socket to do it as the PCB is double sided.
There is low level audio on the volume control which could be used. If you wanted to drive a speaker you would need to run a separate cable to the main body PCB audio amp.
Colin G4EML
You might be able to disconnect those pins from ground and use them for audio but you might need to remove the whole socket to do it as the PCB is double sided.
There is low level audio on the volume control which could be used. If you wanted to drive a speaker you would need to run a separate cable to the main body PCB audio amp.
Colin G4EML