tyt 9600 sensitivity issue
tyt 9600 sensitivity issue
Paint this picture in your head, I have a new TYT9600 V5 with stock firmware, and i cant hit the same repeaters as I can with the old radio ICV-8000, So it tells me that the tyt isnt sensitive enough in the front end, Now if I put the opengd77 firmware on it will it help, I have the opengd77 on all my md uv380 and i love it, but will it help with the sensitivity issue of the tyt9600
Thanks Kb3nun
Eddie
Thanks Kb3nun
Eddie
Re: tyt 9600 sensitivity issue
The performance of the MD9600 is normally quite good. If you are experiencing a noticeable difference to other radios then you may have a hardware fault.
OpenGD77 won't make any difference to the sensitivity.
OpenGD77 won't make any difference to the sensitivity.
Re: tyt 9600 sensitivity issue
Buen día, personalmente correjí la sencibilidad sobre todo en VHF cuando el 9600 estaba con el firmware de fábrica, en el menú oculto al que se accede con "Ctrl+T" reduje el valor del squech de S1 logrando una mejor recepción.
Last edited by LU2BAM on Fri Oct 20, 2023 2:25 pm, edited 1 time in total.
Re: tyt 9600 sensitivity issue
In English please.
Thanks.
---
Daniel
Thanks.
---
Daniel
Re: tyt 9600 sensitivity issue
Pido perdón, no domino el idioma inglés, si molesta lo por mi escrito no tengo problemas en retirarlo y no postear más. Pido nuevamente perdón si he molestado a alguien. Saludos.
Last edited by LU2BAM on Fri Oct 20, 2023 2:21 pm, edited 2 times in total.
Re: tyt 9600 sensitivity issue
Pido perdón, no domino el idioma inglés, si molesta lo por mi escrito no tengo problemas en retirarlo y no posterar más. Pido nuevamente perdón si he molestado a alguien. Saludos.
PD: para leer lo publicado por ustedes utilizo el traductor de Google.
Re: tyt 9600 sensitivity issue
It's not a matter if that bother me, it's an English forum, you have to use it.
You can use Google translate for that, since you're using it to translate to Spanish.
You can use Google translate for that, since you're using it to translate to Spanish.
Re: tyt 9600 sensitivity issue
Receiver sensitivity will not change just installing Opengd77, it's strictly a hardware design characteristic. Maybe you can try to reduce the squelch level (as LU2BAM mentioned), or even better install Opengd77 where is much easier to adjust squelch level.kb3nun wrote: ↑Wed Oct 18, 2023 8:41 pmPaint this picture in your head, I have a new TYT9600 V5 with stock firmware, and i cant hit the same repeaters as I can with the old radio ICV-8000, So it tells me that the tyt isnt sensitive enough in the front end, Now if I put the opengd77 firmware on it will it help, I have the opengd77 on all my md uv380 and i love it, but will it help with the sensitivity issue of the tyt9600
Thanks Kb3nun
Eddie
Re: tyt 9600 sensitivity issue
Vuelvo a pedirle disculpas por escribir en español, no lo sé hacer de otra manera, no se volverá a repetir ya que este será mi último posteo. Por otra parte creo no haber leído en ningún sitio que este foro era en idioma inglés. Le pido nuevamente disculpas si le he causado molestias, no fue mi intención.
Dante Garibaldi - LU2BAM
dante.gari@gmail.com
Re: tyt 9600 sensitivity issue
I have tried adjusting the squelch only way i can hear the repeater is to have the squelch wide open,so i am guessing this radio has a hardware issue, and is still under warrenty