GD-77 programming with Windows 11

DS5HDN
Posts: 6
Joined: Mon Jul 05, 2021 4:34 pm
Location: Busan, Korea

Re: GD-77 programming with Windows 11

Post by DS5HDN » Sat Nov 12, 2022 5:09 am

VK3KYY wrote:
Sat Nov 12, 2022 4:16 am
DS5HDN wrote:
Sat Nov 12, 2022 3:29 am
VK3KYY wrote:
Sat Nov 12, 2022 12:25 am


Does the CPS detect the COM Port device, or do you have to select it manually
The com port selection window appears, but it always fails.
What do you mean 'fails' ?? What error message ?
Only part of the message is remembered Firmware recovery

VK3KYY
Posts: 7478
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia

Re: GD-77 programming with Windows 11

Post by VK3KYY » Sat Nov 12, 2022 5:14 am

DS5HDN wrote:
Sat Nov 12, 2022 5:09 am
VK3KYY wrote:
Sat Nov 12, 2022 4:16 am
DS5HDN wrote:
Sat Nov 12, 2022 3:29 am


The com port selection window appears, but it always fails.
What do you mean 'fails' ?? What error message ?
Only part of the message is remembered Firmware recovery
So this is not writing or reading the codeplug to the radio, its firmwae installation into the GD77 ???

DS5HDN
Posts: 6
Joined: Mon Jul 05, 2021 4:34 pm
Location: Busan, Korea

Re: GD-77 programming with Windows 11

Post by DS5HDN » Sat Nov 12, 2022 5:36 am

VK3KYY wrote:
Sat Nov 12, 2022 5:14 am
DS5HDN wrote:
Sat Nov 12, 2022 5:09 am
VK3KYY wrote:
Sat Nov 12, 2022 4:16 am


What do you mean 'fails' ?? What error message ?
Only part of the message is remembered Firmware recovery
So this is not writing or reading the codeplug to the radio, its firmwae installation into the GD77 ???
Of course, I followed all the steps and installed it.
I installed the Korean language pack on the current English version of Windows 11.
I am using Hangul( Korean language)Windows and opengd77 cps without any problems.
But
If you install Hangul(Korean language) Windows and use opengd77 cps, you cannot communicate with the device.
Last edited by DS5HDN on Sat Nov 12, 2022 5:46 am, edited 1 time in total.

VK3KYY
Posts: 7478
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia

Re: GD-77 programming with Windows 11

Post by VK3KYY » Sat Nov 12, 2022 5:38 am

What do you mean by "Firmware recovery" ?

DS5HDN
Posts: 6
Joined: Mon Jul 05, 2021 4:34 pm
Location: Busan, Korea

Re: GD-77 programming with Windows 11

Post by DS5HDN » Sat Nov 12, 2022 5:43 am

VK3KYY wrote:
Sat Nov 12, 2022 5:38 am
What do you mean by "Firmware recovery" ?
I couldn't understand the exact content of the message because I didn't speak English well.
Among the displayed messages, remember to try again after restoring the device's firmware.

KI7TTO
Posts: 4
Joined: Tue Sep 22, 2020 5:54 am

Re: GD-77 programming with Windows 11

Post by KI7TTO » Tue Jun 13, 2023 4:50 pm

Has there been a resolution to the problem of not connecting to windows 11?

VK3KYY
Posts: 7478
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia

Re: GD-77 programming with Windows 11

Post by VK3KYY » Tue Jun 13, 2023 8:56 pm

KI7TTO wrote:
Tue Jun 13, 2023 4:50 pm
Has there been a resolution to the problem of not connecting to windows 11?
There is no specific problem with Windows 11, it works for a lot of people.

Did you try the latest CPS ??

Post Reply