OpenGD77

Posted: **Wed Sep 21, 2022 7:25 pm**

W8LDO wrote: ↑
Fri Mar 04, 2022 8:19 pm
Anybody else having problems with receive? About one out of every 25 to 50 recieve transmissions are quiet. I can do a channel up and down or down and up, after I notice, and I will begin to hear it again. Do I have something set wrong?

I have found the fix for this. Change the TX Delay in the pi-star settings from 100 to 0 for the modem.

Posted: **Thu Sep 29, 2022 8:02 am**

The stable version of CPS tool is downloaded from there

Posted: **Thu Sep 29, 2022 10:10 am**

BG3IGC wrote: ↑
Thu Sep 29, 2022 8:02 am
The stable version of CPS tool is downloaded from there

Latest CPS is always in

downloads/CPS/Latest/

Posted: **Fri Sep 30, 2022 4:01 am**

Thank you very much

Posted: **Fri Sep 30, 2022 3:36 pm**

W8LDO wrote: ↑
Wed Sep 21, 2022 7:25 pm

W8LDO wrote: ↑
Fri Mar 04, 2022 8:19 pm
Anybody else having problems with receive? About one out of every 25 to 50 recieve transmissions are quiet. I can do a channel up and down or down and up, after I notice, and I will begin to hear it again. Do I have something set wrong?
I have found the fix for this. Change the TX Delay in the pi-star settings from 100 to 0 for the modem.

Personally, in ''Modem'', I configured my ''TXDelay'' at 50 (originally at 100) since it is thus compatible with all of my radios. The ''DMRDelay'' is at 0 and has not been modified.
For the rest, you have to do a calibration procedure.

Posted: **Sat Oct 01, 2022 4:31 am**

ve2ugo wrote: ↑
Fri Sep 30, 2022 3:36 pm

W8LDO wrote: ↑
Wed Sep 21, 2022 7:25 pm

W8LDO wrote: ↑
Fri Mar 04, 2022 8:19 pm
Anybody else having problems with receive? About one out of every 25 to 50 recieve transmissions are quiet. I can do a channel up and down or down and up, after I notice, and I will begin to hear it again. Do I have something set wrong?
I have found the fix for this. Change the TX Delay in the pi-star settings from 100 to 0 for the modem.
Personally, in ''Modem'', I configured my ''TXDelay'' at 50 (originally at 100) since it is thus compatible with all of my radios. The ''DMRDelay'' is at 0 and has not been modified.
For the rest, you have to do a calibration procedure.

any reason for choosing 50 over 0? i haven't had any problems with the 0 setting yet. Is there anything you run into by setting it less than 50?

Posted: **Tue Oct 04, 2022 8:04 pm**

I had some problems at 10 so I didn't go all the way to 0. But it depends on the type of HotSpot you have.
For example, my config are not the same on a Chinese JumboSpot as with a duplex Lonestar.
In addition, with some radios, such as Anytone, some hotspot must make a particular configuration so that it responds well...

Posted: **Wed Oct 05, 2022 5:47 pm**

ve2ugo wrote: ↑
Tue Oct 04, 2022 8:04 pm
I had some problems at 10 so I didn't go all the way to 0. But it depends on the type of HotSpot you have.
For example, my config are not the same on a Chinese JumboSpot as with a duplex Lonestar.
In addition, with some radios, such as Anytone, some hotspot must make a particular configuration so that it responds well...

Posted: **Sat Nov 19, 2022 2:15 am**

Congratulations on the great teamwork!

Posted: **Sat Jan 07, 2023 12:47 am**

Hello
Link to CPS folder does not work. Must I have that CPS or is it possible to load open firmware with original CPS?

73 Gunnar SA5GNO

OpenGD77

Stable release (2022 02 28)

Re: Stable release (2022 02 28)

Re: Stable release (2022 02 28)

Re: Stable release (2022 02 28)

Re: Stable release (2022 02 28)

Re: Stable release (2022 02 28)

Re: Stable release (2022 02 28)

Re: Stable release (2022 02 28)

Re: Stable release (2022 02 28)

Re: Stable release (2022 02 28)

Re: Stable release (2022 02 28)