Unable to load DM-1801 Unstable Firmware with CPS Loader

Post Reply
User avatar
kd2lh
Posts: 312
Joined: Mon Dec 02, 2019 2:44 pm

Unable to load DM-1801 Unstable Firmware with CPS Loader

Post by kd2lh » Thu Jun 11, 2020 1:25 pm

While the stable firmware will load successfully, the unstable 6/10/2020 and 6/11/2020 firmware will not load on my DM-1801. The dialog issues an error: "Wrong Model"... This is with 5/4/2020 stable firmware in the radio.

I can load it with the standalone firmware loader. Once the updated unstable firmware is in the radio, the CPS loader will load the unstable firmware again.

I have the correct cable in usage. During the failure the CPS firmware loader would load the stable firmware.

In reading and checking the radios' codeplugs, I noticed that on the "Basic Information" window, they both show "GD-77" as the "Model Name" for some reason, and I cannot update this on the dialog, and write it to the radio using CPS.

I'm not sure how this model number even got programmed into the radios. Is there a way to update this manually? Could this have caused the problem?

VK3KYY
Posts: 7486
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia

Re: Unable to load DM-1801 Unstable Firmware with CPS Loader

Post by VK3KYY » Thu Jun 11, 2020 10:02 pm

Ummm.

Very strange.

I will try to replicate

User avatar
kd2lh
Posts: 312
Joined: Mon Dec 02, 2019 2:44 pm

Re: Unable to load DM-1801 Unstable Firmware with CPS Loader

Post by kd2lh » Thu Jun 11, 2020 10:36 pm

Both of my DM-1801 radios may have also experienced damage to their calibration.

A few months ago, I reported very low modulation on DMR and very noisy white noise under the voice. This remains the case with these radios.

Today, I restored the factory firmware, and they both still have the problem.

Perhaps I've written to EPROM one too many times on these radios?

VK3KYY
Posts: 7486
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia

Re: Unable to load DM-1801 Unstable Firmware with CPS Loader

Post by VK3KYY » Thu Jun 11, 2020 10:48 pm

The data is not in the EEPROM Calibration in the Flash.

Flash has a much lower rewrite limit, but its still at least 10,000 writes

The problem will be something else.

We don't change the calibration data used by the official firmware any more. As soon as I started to support the DM-1801 the calibration data gets copied to a different location, and the CPS uses that location

User avatar
kd2lh
Posts: 312
Joined: Mon Dec 02, 2019 2:44 pm

Re: Unable to load DM-1801 Unstable Firmware with CPS Loader

Post by kd2lh » Fri Jun 12, 2020 1:57 pm

Please, someone post a copy of a working DM-1801 calibration page for UHF and VHF.

Both my radios have failed, so something in the calibration must be causing the problem.

The failure is occurring on both stock and OpenDM1801 firmware so I doubt it's in the firmware code itself.

User avatar
F1RMB
Posts: 2518
Joined: Sat Nov 16, 2019 5:42 am
Location: Grenoble, France

Re: Unable to load DM-1801 Unstable Firmware with CPS Loader

Post by F1RMB » Fri Jun 12, 2020 4:49 pm

Hi Marc,
kd2lh wrote:
Fri Jun 12, 2020 1:57 pm
Please, someone post a copy of a working DM-1801 calibration page for UHF and VHF.

Both my radios have failed, so something in the calibration must be causing the problem.

The failure is occurring on both stock and OpenDM1801 firmware so I doubt it's in the firmware code itself.

I posted mine a while back
http://www.opengd77.com/viewtopic.php?t ... 0c2d#p7826

Cheers
---
Daniel

VK3KYY
Posts: 7486
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia

Re: Unable to load DM-1801 Unstable Firmware with CPS Loader

Post by VK3KYY » Fri Jun 12, 2020 9:33 pm

The calibration data will be in your Flash backup.

I think at address 0x8F000

Post Reply