OpenGD77

Hello Roger,
I'll try it on my GD77 and RD5R
Ciao
Eugenio

Unfortunately my RD5R does not work with the new firmware and my MMDVM hotspot. I would probably have to make an RX / TX correction at the MMDVM hotspot. Then my other radio devices with the hotspot no longer work. I hope there is still a solution. 73 Stefan, DO2STA

Hi,

do2sta wrote: ↑

Fri May 01, 2020 6:23 am

Unfortunately my RD5R does not work with the new firmware and my MMDVM hotspot. I would probably have to make an RX / TX correction at the MMDVM hotspot. Then my other radio devices with the hotspot no longer work. I hope there is still a solution. 73 Stefan, DO2STA

If you have access to frequency counter, you can check if it's properly aligned.


Cheers.
---
Daniel

do2sta wrote: ↑

Fri May 01, 2020 6:23 am

Unfortunately my RD5R does not work with the new firmware and my MMDVM hotspot. I would probably have to make an RX / TX correction at the MMDVM hotspot. Then my other radio devices with the hotspot no longer work. I hope there is still a solution. 73 Stefan, DO2STA

New firmware .It works fine with my MMDVM hotspot .

do2sta wrote: ↑

Fri May 01, 2020 6:23 am

Unfortunately my RD5R does not work with the new firmware and my MMDVM hotspot. I would probably have to make an RX / TX correction at the MMDVM hotspot. Then my other radio devices with the hotspot no longer work. I hope there is still a solution. 73 Stefan, DO2STA

Unfortunately, I have the same problem and that's why I downloaded the factory software again and my RD-5R connects seamlessly to my two single- and dual-slot hotspots. After uploading OpenRD-5R software I can no longer connect to either hotspot or the other. Only after reducing the frequency -700Hz in TX radio was restored. I can't change anything in the hotspot (Offset), because the other three radios will have the same problem as the RD-5R.

Yesterday, I loaded the April 30 release on both of my GD-77s and they are working beautifully. Thank you for another fine release!

73, Rob W1AEX

Hi,

does anyone else have the problem on FM, especially on repeaters, when the other party is over-modulated (to close to microphone or too much mic gain), the RX on GD77 starts to break (stutter) ? I noticed this on two latest final releases.

Otherwise working great, thank you!

73, de 4O6DTM

4O6DTM wrote: ↑

Fri May 01, 2020 10:20 pm

Hi,

does anyone else have the problem on FM, especially on repeaters, when the other party is over-modulated (to close to microphone or too much mic gain), the RX on GD77 starts to break (stutter) ? I noticed this on two latest final releases.

Otherwise working great, thank you!

73, de 4O6DTM

Maybe this help:
Is just this same version with the RIKU, OH1E mod viewtopic.php?f=11&t=794&start=10#p7848

https://filebin.net/wxlfl201jmx6wip4/Op ... t=2c413w2j <-- opengd77_riku.sgl

Tnx Jordi,

it seems to be the same problem, I haven't noticed until I read that post that all repeaters I noticed the problem on transmit with Ctcss. I will post on that post also.

73, 4O6DTM

Hi
I still have the bug that I mentionned about the previous pre-release
All my 3 GD77 have the same:

When switching from a FM channel towards a DMR channel (only tested towards a busy DMR channel) the RX sound is muted.

DMR -> DMR no problem
FMN -> DMR no problem
FM -> DMR no sound

73 and thanks again for the huge job that's being done