Release 30th April

User avatar
m1dyp
Posts: 406
Joined: Sat Nov 16, 2019 8:03 am
Location: Hertfordshire, U.K.

Re: Release 30th April

Post by m1dyp » Thu Apr 30, 2020 7:58 am

thank you
73 de Ken :D

mimi60
Posts: 22
Joined: Thu Mar 12, 2020 12:50 pm

Re: Release 30th April

Post by mimi60 » Thu Apr 30, 2020 9:28 am

Après mis a jour du firmware:
Tx parfais en UHF
RX faible et beaucoup de souffle !

MM6NRK
Posts: 56
Joined: Wed Apr 22, 2020 1:09 pm

Re: Release 30th April

Post by MM6NRK » Thu Apr 30, 2020 9:49 am

Thanks Again .

User avatar
f6fzo
Posts: 30
Joined: Sat Jan 04, 2020 7:28 am

Re: Release 30th April

Post by f6fzo » Thu Apr 30, 2020 3:11 pm

Merci :mrgreen:
F6FZO Serge 43 Nord

IU1MCR
Posts: 13
Joined: Sun Mar 15, 2020 4:07 pm
Location: Italy Novara - JN45hk

Re: Release 30th April

Post by IU1MCR » Thu Apr 30, 2020 4:12 pm

Hello Roger,
I'll try it on my GD77 and RD5R
Ciao
Eugenio

do2sta
Posts: 3
Joined: Sat Nov 23, 2019 5:22 am
Location: Gelnhausen, Germany
Contact:

Re: Release 30th April

Post by do2sta » Fri May 01, 2020 6:23 am

Unfortunately my RD5R does not work with the new firmware and my MMDVM hotspot. I would probably have to make an RX / TX correction at the MMDVM hotspot. Then my other radio devices with the hotspot no longer work. I hope there is still a solution. 73 Stefan, DO2STA

User avatar
F1RMB
Posts: 681
Joined: Sat Nov 16, 2019 5:42 am
Location: Grenoble, France
Contact:

Re: Release 30th April

Post by F1RMB » Fri May 01, 2020 7:47 am

Hi,
do2sta wrote:
Fri May 01, 2020 6:23 am
Unfortunately my RD5R does not work with the new firmware and my MMDVM hotspot. I would probably have to make an RX / TX correction at the MMDVM hotspot. Then my other radio devices with the hotspot no longer work. I hope there is still a solution. 73 Stefan, DO2STA
If you have access to frequency counter, you can check if it's properly aligned.


Cheers.
---
Daniel
73 de Daniel.

MM6NRK
Posts: 56
Joined: Wed Apr 22, 2020 1:09 pm

Re: Release 30th April

Post by MM6NRK » Fri May 01, 2020 8:43 am

do2sta wrote:
Fri May 01, 2020 6:23 am
Unfortunately my RD5R does not work with the new firmware and my MMDVM hotspot. I would probably have to make an RX / TX correction at the MMDVM hotspot. Then my other radio devices with the hotspot no longer work. I hope there is still a solution. 73 Stefan, DO2STA
New firmware .It works fine with my MMDVM hotspot .

SO5AJG
Posts: 60
Joined: Sat Nov 16, 2019 3:44 pm

Re: Release 30th April

Post by SO5AJG » Fri May 01, 2020 10:44 am

do2sta wrote:
Fri May 01, 2020 6:23 am
Unfortunately my RD5R does not work with the new firmware and my MMDVM hotspot. I would probably have to make an RX / TX correction at the MMDVM hotspot. Then my other radio devices with the hotspot no longer work. I hope there is still a solution. 73 Stefan, DO2STA
Unfortunately, I have the same problem and that's why I downloaded the factory software again and my RD-5R connects seamlessly to my two single- and dual-slot hotspots. After uploading OpenRD-5R software I can no longer connect to either hotspot or the other. Only after reducing the frequency -700Hz in TX radio was restored. I can't change anything in the hotspot (Offset), because the other three radios will have the same problem as the RD-5R.
Janusz - SO5AJG - Warsaw

User avatar
W1AEX
Posts: 107
Joined: Sat Nov 16, 2019 9:00 pm
Location: Connecticut, USA
Contact:

Re: Release 30th April

Post by W1AEX » Fri May 01, 2020 5:16 pm

Yesterday, I loaded the April 30 release on both of my GD-77s and they are working beautifully. Thank you for another fine release!

73, Rob W1AEX

Post Reply