Update 22nd Jan

User avatar
F1RMB
Posts: 410
Joined: Sat Nov 16, 2019 5:42 am
Location: Grenoble, France
Contact:

Re: Update 22nd Jan

Post by F1RMB » Wed Jan 22, 2020 10:51 pm

kd2lh wrote:
Wed Jan 22, 2020 10:37 pm
CWID is working on this version firmware, but the first "dah" of the "D" "-.." in "DE AB1XYZ" is cut off when I listen to the transmission in analog FM.

Could a brief delay be included after the transmitter is activated and before the first of the morse is sent?

Marc

Yup, that's possible. I'll do that tomorrow.

Cheers.
---
Daniel
73 de Daniel.

G0NHF
Posts: 26
Joined: Sun Jan 19, 2020 10:28 am

Re: Update 22nd Jan

Post by G0NHF » Wed Jan 22, 2020 11:08 pm

Has the +6dB DMR receive audio been added to this firmware?
Thanks once again
Tony G0NHF

VK3KYY
Posts: 1630
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia
Contact:

Re: Update 22nd Jan

Post by VK3KYY » Wed Jan 22, 2020 11:26 pm

The +6db will be in this version, as Daniel uses the Master version of the source code as his base

G0NHF
Posts: 26
Joined: Sun Jan 19, 2020 10:28 am

Re: Update 22nd Jan

Post by G0NHF » Thu Jan 23, 2020 10:43 am

Thank you Roger :D
Tony

F6GVE
Posts: 43
Joined: Sat Nov 16, 2019 8:52 am

Re: Update 22nd Jan

Post by F6GVE » Thu Jan 23, 2020 9:43 pm

Intensively tested one day long, including hotspot mode, and I found no new bug.
Sometimes, when scanning CC, it happens after a while that the firmware crashes, but this is not new nor very important (to my opinion)
Good job :)

VK3KYY
Posts: 1630
Joined: Sat Nov 16, 2019 3:25 am
Location: Melbourne, Australia
Contact:

Re: Update 22nd Jan

Post by VK3KYY » Thu Jan 23, 2020 10:46 pm

F6GVE wrote:
Thu Jan 23, 2020 9:43 pm
...
I found no new bug.
Sometimes, when scanning CC, it happens after a while that the firmware crashes...
I think the CC scanning bug was in previous versions. We probably need to slow down the CC scanning, because the usual cause of a crash is trying to do things too quickly, and causing 2 parts of the firmware to try to access the hardware at the same time.

F6GVE
Posts: 43
Joined: Sat Nov 16, 2019 8:52 am

Re: Update 22nd Jan

Post by F6GVE » Fri Jan 24, 2020 2:12 pm

VK3KYY wrote:
Thu Jan 23, 2020 10:46 pm
F6GVE wrote:
Thu Jan 23, 2020 9:43 pm
...
I found no new bug.
Sometimes, when scanning CC, it happens after a while that the firmware crashes...
I think the CC scanning bug was in previous versions. We probably need to slow down the CC scanning, because the usual cause of a crash is trying to do things too quickly, and causing 2 parts of the firmware to try to access the hardware at the same time.
You are right. During a CC scaning the firmware crashed everytime and very quickly with some previous versions. Recently I found no crash any longer, but with version Jan 22 2020 13:59:37 [787229b] I have some crashes again.
73
Luc

G4EML
Posts: 175
Joined: Sat Nov 16, 2019 10:01 am

Re: Update 22nd Jan

Post by G4EML » Fri Jan 24, 2020 3:07 pm

When the colour code scan crashes are you trying to receive an amateur system or a commercial one? It is important to know this because commercial systems are likely to use data modes not supported by OpenGD77.

F6GVE
Posts: 43
Joined: Sat Nov 16, 2019 8:52 am

Re: Update 22nd Jan

Post by F6GVE » Fri Jan 24, 2020 5:20 pm

Some hours ago, it crashed repetitively, it doesn't any longer...
I tried commercial repeaters, amateur repeaters, when the frequency is free of DMR, or not, and I could not make it crash again.
The only thing I can say is that the scan speed is bit higher if the screen indicates TG99 instead of TG20883...
(I used 2 openGD77 to compare, to monitor the frequency, etc.)
I'll try again with 100% charged battery ...

User avatar
KV0A
Posts: 15
Joined: Tue Dec 17, 2019 11:19 pm

Re: Update 22nd Jan

Post by KV0A » Sat Jan 25, 2020 7:06 am

Thanks yet again for the excellent work!

(I promise I'm going to dig into the code myself at some point to see if I can be of any use but for now I've been dealing with HF antenna issues.... Just got an HF rig, finally.)
Robert - KV0A

Post Reply