-
F1RMB
- Posts: 2608
- Joined: Sat Nov 16, 2019 5:42 am
- Location: Grenoble, France
Post
by F1RMB » Wed Jan 22, 2020 10:51 pm
kd2lh wrote: ↑Wed Jan 22, 2020 10:37 pm
CWID is working on this version firmware, but the first "dah" of the "D" "-.." in "DE AB1XYZ" is cut off when I listen to the transmission in analog FM.
Could a brief delay be included after the transmitter is activated and before the first of the morse is sent?
Marc
Yup, that's possible. I'll do that tomorrow.
Cheers.
---
Daniel
-
G0NHF
- Posts: 46
- Joined: Sun Jan 19, 2020 10:28 am
Post
by G0NHF » Wed Jan 22, 2020 11:08 pm
Has the +6dB DMR receive audio been added to this firmware?
Thanks once again
Tony G0NHF
-
VK3KYY
- Posts: 7589
- Joined: Sat Nov 16, 2019 3:25 am
- Location: Melbourne, Australia
Post
by VK3KYY » Wed Jan 22, 2020 11:26 pm
The +6db will be in this version, as Daniel uses the Master version of the source code as his base
-
G0NHF
- Posts: 46
- Joined: Sun Jan 19, 2020 10:28 am
Post
by G0NHF » Thu Jan 23, 2020 10:43 am
Thank you Roger
Tony
-
F6GVE
- Posts: 84
- Joined: Sat Nov 16, 2019 8:52 am
Post
by F6GVE » Thu Jan 23, 2020 9:43 pm
Intensively tested one day long, including hotspot mode, and I found no new bug.
Sometimes, when scanning CC, it happens after a while that the firmware crashes, but this is not new nor very important (to my opinion)
Good job
-
VK3KYY
- Posts: 7589
- Joined: Sat Nov 16, 2019 3:25 am
- Location: Melbourne, Australia
Post
by VK3KYY » Thu Jan 23, 2020 10:46 pm
F6GVE wrote: ↑Thu Jan 23, 2020 9:43 pm
...
I found no new bug.
Sometimes, when scanning CC, it happens after a while that the firmware crashes...
I think the CC scanning bug was in previous versions. We probably need to slow down the CC scanning, because the usual cause of a crash is trying to do things too quickly, and causing 2 parts of the firmware to try to access the hardware at the same time.
-
F6GVE
- Posts: 84
- Joined: Sat Nov 16, 2019 8:52 am
Post
by F6GVE » Fri Jan 24, 2020 2:12 pm
VK3KYY wrote: ↑Thu Jan 23, 2020 10:46 pm
F6GVE wrote: ↑Thu Jan 23, 2020 9:43 pm
...
I found no new bug.
Sometimes, when scanning CC, it happens after a while that the firmware crashes...
I think the CC scanning bug was in previous versions. We probably need to slow down the CC scanning, because the usual cause of a crash is trying to do things too quickly, and causing 2 parts of the firmware to try to access the hardware at the same time.
You are right. During a CC scaning the firmware crashed everytime and very quickly with some previous versions. Recently I found no crash any longer, but with version Jan 22 2020 13:59:37 [787229b] I have some crashes again.
73
Luc
-
G4EML
- Posts: 928
- Joined: Sat Nov 16, 2019 10:01 am
Post
by G4EML » Fri Jan 24, 2020 3:07 pm
When the colour code scan crashes are you trying to receive an amateur system or a commercial one? It is important to know this because commercial systems are likely to use data modes not supported by OpenGD77.
-
F6GVE
- Posts: 84
- Joined: Sat Nov 16, 2019 8:52 am
Post
by F6GVE » Fri Jan 24, 2020 5:20 pm
Some hours ago, it crashed repetitively, it doesn't any longer...
I tried commercial repeaters, amateur repeaters, when the frequency is free of DMR, or not, and I could not make it crash again.
The only thing I can say is that the scan speed is bit higher if the screen indicates TG99 instead of TG20883...
(I used 2 openGD77 to compare, to monitor the frequency, etc.)
I'll try again with 100% charged battery ...
-
KV0A
- Posts: 16
- Joined: Tue Dec 17, 2019 11:19 pm
Post
by KV0A » Sat Jan 25, 2020 7:06 am
Thanks yet again for the excellent work!
(I promise I'm going to dig into the code myself at some point to see if I can be of any use but for now I've been dealing with HF antenna issues.... Just got an HF rig, finally.)