Page 41 of 69
Re: New ongoing "Development" version has been created
Posted: Thu Nov 05, 2020 8:15 pm
by VK3KYY
I have 2 radios running at the same time.
One with the version from 2020.11.03 and one from 2020.11.05 and I tested on FM and I don't see any difference in signal level on either simplex or duplex DMR or on FM.
However, the RSSI sampling timing was changed, because in the previous versions when scanning, sometimes the RSSI was not being read because of a clash with the EEPROM and the RF chip both sharing the I2C bus
Re: New ongoing "Development" version has been created
Posted: Thu Nov 05, 2020 8:21 pm
by Ik0nwg
VK3KYY wrote: ↑Thu Nov 05, 2020 7:44 pm
n1id wrote: ↑Thu Nov 05, 2020 7:32 pm
I do not have parrot or disconnect work at all under nov 5 on 3-gd77's also i notice that the signal it receives from my hotspot was about half scale varying instead of full bar which it should be. Nov 3 works fine
OK.
I made some changes to DMR RSSI sample timing,
Is the signal strength correct if change to FM and listen to the hotspot?
I don't even hear the noise of the DMR on FM .... if I move between channels and then go back to my channel I can perfectly hear the noise of the DMR ... customized or non-customized power the problem is always present .... just change channel for an instant and go back to our channel again and you can perfectly hear both the noise of the DMR if we are on FM and our repeated voice that comes from BM
ciao Roger
Re: New ongoing "Development" version has been created
Posted: Thu Nov 05, 2020 8:29 pm
by VK3KYY
Hi Sal
Is this after the end of Tx ?
e.g.
Tx
Then no sigal
Change channel and return to original channel
Then signal can be heard ?
Re: New ongoing "Development" version has been created
Posted: Thu Nov 05, 2020 8:37 pm
by Ik0nwg
VK3KYY wrote: ↑Thu Nov 05, 2020 8:29 pm
Hi Sal
Is this after the end of Tx ?
e.g.
Tx
Then no sigal
Change channel and return to original channel
Then signal can be heard ?
si esatto vado in TX su BM con PC9990 parlo per qualche secondo ..... aspetto e vedo il segnale di ritorno di BM ma non sento la mia voce .... cambio canale e poi ritono sul mio canale e sento perfettamente la mia voce
| google_translate > "yes exactly I go to TX on BM with PC9990 I talk for a few seconds ..... I wait and see the return signal of BM but I don't hear my voice .... I change channel and then I return to my channel and I hear mine perfectly voice"
Re: New ongoing "Development" version has been created
Posted: Thu Nov 05, 2020 8:53 pm
by Ik0nwg
Ik0nwg wrote: ↑Thu Nov 05, 2020 8:37 pm
VK3KYY wrote: ↑Thu Nov 05, 2020 8:29 pm
Hi Sal
Is this after the end of Tx ?
e.g.
Tx
Then no sigal
Change channel and return to original channel
Then signal can be heard ?
si esatto vado in TX su BM con PC9990 parlo per qualche secondo ..... aspetto e vedo il segnale di ritorno di BM ma non sento la mia voce .... cambio canale e poi ritono sul mio canale e sento perfettamente la mia voce
| google_translate > "yes exactly I go to TX on BM with PC9990 I talk for a few seconds ..... I wait and see the return signal of BM but I don't hear my voice .... I change channel and then I return to my channel and I hear mine perfectly voice"
sorry I forgot to do the translation !!! I go to bed to rest
Re: New ongoing "Development" version has been created
Posted: Thu Nov 05, 2020 8:57 pm
by VK3KYY
Guys
I have deleted this release until I can understand what is causing the heating problems.
I don't think the problem has been specifically caused by the changes to add User Power level, I think this is more likely to be an existing bug, which has been awakened by this change
Re: New ongoing "Development" version has been created
Posted: Thu Nov 05, 2020 9:08 pm
by F1RMB
Ik0nwg wrote: ↑Thu Nov 05, 2020 8:53 pm
Ik0nwg wrote: ↑Thu Nov 05, 2020 8:37 pm
VK3KYY wrote: ↑Thu Nov 05, 2020 8:29 pm
Hi Sal
Is this after the end of Tx ?
e.g.
Tx
Then no sigal
Change channel and return to original channel
Then signal can be heard ?
si esatto vado in TX su BM con PC9990 parlo per qualche secondo ..... aspetto e vedo il segnale di ritorno di BM ma non sento la mia voce .... cambio canale e poi ritono sul mio canale e sento perfettamente la mia voce
| google_translate > "yes exactly I go to TX on BM with PC9990 I talk for a few seconds ..... I wait and see the return signal of BM but I don't hear my voice .... I change channel and then I return to my channel and I hear mine perfectly voice"
sorry I forgot to do the translation !!! I go to bed to rest
No worries
Goodnight !
---
Daniel
Re: New ongoing "Development" version has been created
Posted: Fri Nov 06, 2020 7:21 am
by f6fzo
Bonne nuit hihihihihihi
Re: New ongoing "Development" version has been created
Posted: Fri Nov 06, 2020 7:49 am
by EB3AM
F1RMB wrote: ↑Thu Nov 05, 2020 4:27 pm
EB3AM wrote: ↑Thu Nov 05, 2020 3:51 pm
F1RMB wrote: ↑Thu Nov 05, 2020 3:19 pm
Hi,
Scanning a Zone or "All Channels" ? In case of a Zone, DMR or FM only, a mix of both, how many channels ? (just to try to reproduce your conditions).
Cheers.
---
Daniel
Hi Daniel
All channels, mix of DMR and FM channels, about 100.
Also I remove TS filter. Color filter is enabled.
Okay. I will let it run in the same conditions.
Cheers.
---
Daniel
I try to repeat this night but the radio has cold at one hour running scan.
maybe is a astral position of mars...
Re: New ongoing "Development" version has been created
Posted: Fri Nov 06, 2020 7:54 am
by F1RMB
Hi,
EB3AM wrote: ↑Fri Nov 06, 2020 7:49 am
I try to repeat this night but the radio has cold at one hour running scan.
maybe is a astral position of mars...
Yes, most probably
Cheers.
---
Daniel